MaxStream XStream-Pkg Manuale Pagina 46
- Pagina / 62
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
XStream‐PKG‐T™TelephoneRFModem–ProductManualv5.x00[2006.02.24]
When the BD command is sent with a non-standard interface data rate, the UART will adjust to
accommodate the requested interface rate. In most cases, the clock resolution will cause the
stored BD parameter to vary from the parameter that was sent (refer to the table below).
Reading the BD command (send "ATBD" command without an associated parameter value) will
return the value that was actually stored to the BD register.
ParameterSentvs.Pa rameterStored
BD Parameter Sent (HEX) Interface Data Rate (bps) BD Parameter Stored (HEX)
0 1200 0
4 19,200 4
7 115,200 7
12C 300 12B
1C200 115,200 1B207
BK (Serial Break Passing) Command
AT Command: ATBK
Binary Command: 0x2D (45 decimal)
Parameter Range: 0 – 1
Parameter Configuration
0 disable
1 enable
Default Parameter Value: 0
Number of bytes returned: 1
Minimum Firmware Version Required: 4.30
<Serial Interfacing> Pass a serial break condition
on the DI pin to the DO pin of another modem.
BO (Serial Break Timeout) Command
<Serial Interfacing> DO pin will return to default
after no serial break status information is
received during the timeout period.
AT Command: ATBO
Binary Command: 0x2F (47 decimal)
Parameter Range: 0 – 0xFFFF [x 1 second]
Default Parameter Value: 0
Number of bytes returned: 2
Related Commands: BK (Serial Break Passing)
Minimum Firmware Version Required: 4.30
Use with BK = 1.
BT (Guard Time Before) Command
<AT Command Mode Options> BT Command is
used to set/read the DI pin silence time that
must precede the command sequence character
(CC Command) of the AT Command Mode
Sequence.
AT Command: ATBT
Binary Command: 0x04 (4 decimal)
Parameter Range: 2 – 0xFFFF
©2006MaxStream,Inc.,ConfidentialandProprietary 46
The default sequence used to enter AT Command
Mode is as follows:
• No characters sent for 1 second
[BT (Guard Time Before) Command]
• Send three plus characters “---”
[CC (Command Sequence Character) Command]
[x 100 milliseconds]
Default Parameter Value: 0x0A (10 decimal)
Number of bytes returned: 2
Related Commands: AT (Guard Time After),
CC (Command Sequence Character)
• No characters sent for 1 second [AT (Guard Time After) Command]
All of the values in this sequence can be adjusted.
Fast AT Command Mode Entry. Set AT and BT parameters to 0 for 0.6 second guard times.
Beware that this will also mean that AT Command Mode cannot be entered by manually typing
the AT command sequence characters (“---” by default) because the BT timeout will occur faster
than the characters can be typed.
www.agelectronica.com www.agelectronica.com
www.agelectronica.com www.agelectronica.com
- Product Manual v5.x00 1
- Contents 3
- 1.1. Key Features 4
- 1.2. Product Overview 5
- 1.3. External Interface 6
- 1.4. Block Diagram 7
- 1.5. Pin Signals 8
- 2. RFModuleOperation 9
- 2.1.2. Transmit Mode 10
- 2.1.3. Receive Mode 11
- 2.1.4. Sleep Mode 12
- 2.1.5. Command Mode 14
- 2.2. RF Module Configuration 15
- 2.2.2. AT Command Mode 16
- 2.2.3. Binary Command Mode 18
- 4. RFCommunicationModes 26
- 4.1. Addressing 27
- 4.2. Basic Communications 28
- 4.2.2. Repeater Mode 29
- 4.3.1. Acknowledged Mode 32
- 4.3.2. Multi-Streaming Mode 34
- FCC Certification 38
- OEM Labeling Requirements 39
- Antenna Usage 40
- FCC-Approved Antennas 41
- Mechanical Drawings 43
- RF Module Configuration 44
- 1-Year Warranty 61
- Ordering Information 61
- Contact MaxStream 62
Prodotti e manuali riguardandi Networking MaxStream XStream-Pkg
Networking MaxStream 9XTend-PKG-E Manuale
(62 pagine)
(62 pagine)
Sangean U2 (V1) manuals
Owner’s manuals and user’s guides for Radio Sangean U2 (V1).
We providing 4 pdf manuals Sangean U2 (V1) for download free by document types: User Manual
Table of contents
Table of contents
Table of contents
Table of contents
More products and manuals for Radio Sangean
| Models | Document Type |
|---|---|
| UCR-100 (V1) |
User Manual
Sangean UCR-100 (V1) Benutzerhandbuch,
14 pages
|
| UCR-100 (V1) |
User Manual
Sangean UCR-100 (V1) Manual del usuario,
14 pages
|
| UCR-100 (V1) |
User Manual
Sangean UCR-100 (V1) Manuel d'utilisation,
14 pages
|
| UCR-100 (V1) |
User Manual
Sangean UCR-100 (V1) User Manual,
14 pages
|
| WFR-1 (V1) |
User Manual
Sangean WFR-1 (V1) Benutzerhandbuch,
39 pages
|
| WFR-1 (V1) |
User Manual
Sangean WFR-1 (V1) Manual del usuario,
39 pages
|
| WFR-1 (V1) |
User Manual
Sangean WFR-1 (V1) Manuel d'utilisation,
39 pages
|
| WFR-1 (V1) |
User Manual
Sangean WFR-1 (V1) User Manual,
39 pages
|
| WFR-1 (R1) |
User Manual
Sangean WFR-1 (R1) Benutzerhandbuch,
41 pages
|
| WFR-1 (R1) |
User Manual
Sangean WFR-1 (R1) Manuel d'utilisation,
42 pages
|
| WFR-1 (R1) |
User Manual
Sangean WFR-1 (R1) User Manual,
41 pages
|
| WFR-1D+ (V1) |
User Manual
Sangean WFR-1D+ (V1) Benutzerhandbuch,
46 pages
|
| WFR-1D+ (V1) |
User Manual
Sangean WFR-1D+ (V1) Manuel d'utilisation,
46 pages
|
| WFR-1D+ (V1) |
User Manual
Sangean WFR-1D+ (V1) User Manual,
46 pages
|
| WFR-20 (R1) |
User Manual
Sangean WFR-20 (R1) Benutzerhandbuch,
59 pages
|
| WFR-20 (R1) |
User Manual
Sangean WFR-20 (R1) Manual del usuario,
59 pages
|
| WFR-20 (R1) |
User Manual
Sangean WFR-20 (R1) Manuel d'utilisation,
59 pages
|
| WFR-20 (R1) |
User Manual
Sangean WFR-20 (R1) User Manual,
59 pages
|
| WFT-1 (R1) |
User Manual
Sangean WFT-1 (R1) Benutzerhandbuch,
30 pages
|
| WFT-1 (R1) |
User Manual
Sangean WFT-1 (R1) Manual del usuario,
30 pages
|
© 2020, manymanuals.it. Tutti i diritti riservati | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale